8.0 Quick Start

<< Click to Display Table of Contents >>

Navigation:  »No topics above this level«

8.0 Quick Start

 

This Quick Start Guide is designed to help the user to familiarize themselves with the equipment and perform basic setup. For detailed information, please refer to the Setup and Operation Manual.

 

The ECD SmartDRY™ Cabinet is ready to plug in and begin using as soon as it is safely set up. The Cabinet is preset to meet the requirement of J-STD 033 for the safe storage of Moisture Sensitive Components. No additional programming is required. Once unpacked, here are some steps to quickly get your Cabinet up and running.

 

Although pre-programmed to meet the requirement of J-STD 033, the Cabinet must run for a minimum of 8 hours to acclimate and regenerate its dryer module. Please allow this time before adding your moisture sensitive components. Also, the alarm limits have been pre-programmed however, are not enabled. Once the Cabinet has stabilized at set point, the alarms can be enabled if desired. You may also want to explore the other Alarms: SmartDRY™ Temperature, SmartBAKE™ RH, and SmartBAKE™ Temperature, enabling them as you wish. Refer to section 9.1.2 Alarms (SmartDRY™) in the Setup and Operation Manual for detailed information.

Important Information

When accessing options that require a Passcode the system default Passcode is 314. As you enter protected options, you will be prompted to enter it using the Up or Down buttons. Once selected, all locked options remain “unlocked” until you return to the Main Display.

 

1)When prompted, Press and hold the Up or Down button to navigate to Passcode 314. Press the OK button to be able to edit the protected field.

ui_display_(navigate_passcode_314)     ui_display_(select_passcode_314)

 

8.1 Safety and Installation

Make sure you have read and follow the 4.0 Operators Safety Information and 5.0 Setup recommendations in the previous sections.

 

8.2 Location

Move the ECD SmartDRY™ Cabinet into the desired position. Refer to topic 5.2 Location for minimum distance. When selecting a site for the Cabinet, consider conditions which may affect performance, such as heat from radiators, ovens, production equipment, etc. Avoid direct sun, fast-moving air currents, heating/cooling ducts etc. To ensure air circulation, allow a minimum of 75 mm (3”) between the unit and any walls or partitions which might obstruct free air flow.

 

8.3 Shelf Configuration

Install the shelves to meet your storage requirements.

sd-10_shelf_install

8.4 Power

Connect to properly grounded power plug.

wall_socket-plug

8.5 Time Settings

Set the Real Time Clock and ALL time settings for your location.

 

To set the Time:

1)From the Main Display, enter the Main menu by pressing the Menu button. enter the Other Settings menu by pressing the Settings button.

ui_display_(select_main_menu)     ui_display_(select_other_settings_menu)

2)Enter the Date/Time Settings by pressing the Time button.

ui_display_(select_date-time_settings)     ui_display_(date-time_menu-top)

3) Edit the desired settings selecting the OK button to accept each edited value.

ui_display_(navigate_daylight_saving_options)     ui_display_(select_time-zone)

4)To exit the screen, select the Back button which takes you “Back” to the previous menu.

8.6 Clear History

Clear the stored memory. Performing this step clears unwanted data and starts logging data new data from this point on.

 

To clear history:

1)From the Main Display, enter the Main menu by pressing the Menu button. enter the Other Settings menu by pressing the Settings button.

ui_display_(select_main_menu)     ui_display_(select_other_settings_menu)

2)Enter the Data Logging Settings by pressing the button. Press the Clear History button.

ui_display_(select_data_logging_menu)     ui_display_(select_clear_history_settings)

3)To exit the screen, select the Back button which takes you “Back” to the previous menu.